remington model 12 .22 rifle serial number

Then, push fore-end (31) forward slightly over outer magazine tube (29). Hold rifle with left side down, and pull guard and stock assembly rearward out of receiver (14).Ĥ Depress latch of inner magazine tube (15) and pull tube out forward. Loosen takedown screw (6) and pull out to left as far as it will go. Push out hammer bushing (53) to right and lift off hammer and rod,ġ Before starting disassembly, unload the magazine and clear the chamber. Force mainspring (48) forward and insert a short wire through hole in mainspring rod (47). Pull trigger (42) and lower hammer (54) with thumb. Insert long-shank screwdriver in stock hole and remove stock bolt (35) and washer (36) pull guard (41) from stock (34). Unscrew buttplate screws (33) and take off buttplate (32). Also, cock the hammer (54).Ħ If rifle has tang rear sight (39), turn out screws (40) and remove sight. On reassembly, depress rear of breechblock to cause engagement with action bar (27). This is sufficient takedown for normal cleaning. Press down at center of breechblock (9) while sliding fore-end forward, and remove breechblock. Parts are number keyed to parts legend.Ģ Invert receiver assembly and move fore-end (31) rearward, depressing action bar plunger (23) so that it clears the receiver. Rifle is loaded and cocked, safety off, action bar locked by carrier.

Drive ejector pin (4) and firing pin pin (3) upward to release firing pin (8).Ĭutaway shows relationship between assembled parts. Turning the blade slightly forces plunger back against spring (10), and moves rear of extractor out of breechblock. 12F and 12FS, listed at $105.50 in the 1918-19 Remington catalog.Įxtensively produced through the years, the Model 12 was superseded in 1936 by the Remington Model 121 rifle which was similar to the Model 12 but featured an improved firing pin, stock, and fore-end.ģ To remove extractor (11), insert thin-bladed screwdriver between extractor and extractor plunger (12). Spccial features of these deluxe rifles are checkering, engraving, and selected wood. The S in these designations denotes rifles chambered for the. 12C, this rifle has open sights.ĭeluxe versions of the Model 12 arc the No. 22 Remington Spccial (.22 W.R.F.) cartridge. It is equipped with a hooded target front sight, aperture rear sight on the action, and a target-style sling strap.Īnother variation of the 12C rifle is the No. 22 long rifle cartridge, this rifle has a 24' octagon barrel and weighs six lbs. Target Grade was designed for use in matches sponsored by the National Rifle Association. 12B, fires shorts, longs, and long rifles.Ī variation of the 12C called the No. This rifle was used extensively by shooting galleries. 12B Gallery Special Grade has a 24' octagon barrel and is chambered for the. There are several other versions of the Model 12. Its magazine holds 16 short, 12 long, or 11 long rifle cartridges. This version has a 22' round barrel and weighs 4Vi lbs. 22 short, long, and long rifle cartridges interchangeably and without adjustment. The most often encountered Model 12 rifle is the No. Trigger pin center-fire rifle designed by Pcdersen. This system was used also in the Remington Model 14 slide-actionĢ. While normally used as a repeater, the rifle also can be loaded singly through the ejection port in the receiver.Ī single locking lug integral with the upper front of the breechblock engages a shoulder in the receiver just behind the barrel.

Its simple reliable action is trim and compact, and is closed at the rear which helps protect the user from rearward escaping gas in the event of a burst cartridge case. This concealed-hammer repeater with tubular magazine under the barrel is of takedown style and has a crossbolt safety in the trigger guard. 22 rimfire slide-action rifle was introduced in 1909. Illustrations By DENNIS RIORDAN Text By LUDWIG OLSONĭeveloped by the late John D.

Remington model 12 .22 rifle serial number